JOPSS - Search Results

Journal Articles

Prediction of heater surface temperature change at subcooled flow boiling DNB

Liu, W.; Podowski, M. Z.*

Nihon Kikai Gakkai Netsu Kogaku Konfarensu 2015 Koen Rombunshu (CD-ROM), 2 Pages, 2015/10

This paper gives prediction to the transient heat transfer at Departure of Nucleate Boiling (DNB) point for subcooled flow boiling. The prediction is carried out by solving the heat conduction equations in cylindrical coordinates with convective boundary condition, which changes with the change of the heat transfer mode on the heated surface. DNB is assumed to happen at the complete dryout of liquid sublayer trapped between the heated wall and an elongated vapor clot, during the passing time of the vapor clot. Important parameters including initial thickness of the liquid sublayer, vapor clot length, vapor clot velocity and void fraction etc., are calculated from the Liu - Nariai model. The initial heater surface temperature is derived from the Jens-Lottes correlation. The transient changes of liquid sublayer thickness, surface temperature at DNB are reported. No obvious temperature jumping is observed at DNB. To predict temperate excursion at Critical Heat Flux (CHF), more simulations to the transient boiling and film boiling processes are needed.

Journal Articles

Spectroscopic diagnostics for ITER

Sugie, Tatsuo; Costley, A. E.*; Malaquias, A.*; Walker, C.*

Purazuma, Kaku Yugo Gakkai-Shi, 79(10), p.1051 - 1061, 2003/10

http://ci.nii.ac.jp/naid/10011562719

The main regions - the core, the edge, the scrape-off layer, and the divertor - will be probed by an extensive array of spectroscopic instrumentation covering the visible to X-ray wavelength range. Plasma parameters will be determined including impurity species/density/input-flux, ion temperature, He density, fueling ratio, plasma rotation, effective ionic charge and safety factor q. The measurements will be used for plasma control and in studies to understand and improve the performance of ITER. A diagnostic neutral beam (~100 keV) will be installed for Charge Exchange Recombination Spectroscopy. Motional Stark Effect measurements (for q profile) will be made using the heating beam (1 MeV). Diagnostic components, such as mirrors, windows, and optical fibers etc, mounted close to the plasma will experience higher levels of radiation due to neutron, gamma ray and particle irradiations than in present devices. Potentially their performance characteristics can be degraded and so the materials of the components have to be carefully selected and mitigating methods adopted where possible.

Journal Articles

NSRR tests under simulated power oscillation conditions of BWRs

Nakamura, Jinichi; Nakamura, Takehiko; Sasajima, Hideo; Suzuki, Motoe; Uetsuka, Hiroshi

HPR-359, Vol.2, p.34_1 - 34_16, 2002/09

In BWR, power oscillations can occur due to the void fraction fluctuation. To investigate the fuel behavior during power oscillation of BWRs, two types of irradiated fuel rods were tested under simulated power oscillation conditions in the Nuclear Safety Research Reactor(NSRR). One is high burnup BWR fuel (56GWd/t) test, with 4 power oscillation cycles, to clarify the behavior of high burnup fuel. The second one is high enriched fuel(20%,25GWd/t) test, with 7 power cycles, to perform the test under high power conditions. The fuel behavior data, such as cladding elongation, fuel stack elongation, cladding temperature, etc. were obtained in these tests. The DNB did not occur in these tests. The PCI was observed through cladding elongation and fuel stack elongation during the power oscillations, but the residual strain of cladding was very small. Fuel behavior under simulated power oscillations is discussed based on in-pile data and PIE data and is compared with FEMAXI-6 and FRAP-T6 calculation.

JAEA Reports